Hunter ceiling fans are reliable and they are renowned for it but sometimes things can go wrong. If your Hunter Light is not working, you do not need to worry. There are a few simple fixes that can help you to fix the light within no time. We have added the fixes from expert professionals, here is how you can diagnose the problem and fix your fan light.
If your ceiling fan light is not working, these are the possible causes and what you can do about it:
- A broken light bulb or light kit – Ensure that the bulbs are tight with screws properly. If it still doesn’t turn on, change the light bulbs with a replacement or get a new light kit.
- An electrical issue – Check the electrical wiring to find a loose cable, broken cable, or a defective regulator. If there are broken parts replace them. If nothing seems broken, the next thing is to reset the breaker.
- A defective remote control – Reset the remote control by replacing the batteries with new ones or test if there are any problems with the frequency.
If you give preference to do the minor electrical work on your own, you can take down the fixture after removing it, and change the defective parts yourself. Read this guide to follow the troubleshooting process.
Why Is My Hunter Ceiling Fan Light Not Working?
Hunter is a renowned brand and provides some of the best ceiling fans because their units are reliable, well-made and come with a limited lifetime warranty on the fan motors. However, you may face issues related to the electrical wiring and switches that control the light.
If the lights on your Hunter fan are not working, follow the given steps below:
A Faulty Light Bulb
Your ceiling fan is working but lights are not?
The first step you need to take when you see that your hunter ceiling fan light isn’t working is to examine the bulb. Is it burned out? Is it loose in the socket and could be jiggled out?
If that is the case, try to replace the bulb with a new bulb, and after doing so, screw it in tightly.
Most modern bulb are designed with safety feature that save them from burning out, so if the bulb is not working, you may need to change it. The only thing you need to keep in mind while replacing them is the correct wattage for the light kit.
If you have recently replaced the bulb and it is not lighting up, switch off the ceiling fan power and wait for 30 seconds and turn it back on.
If your Hunter fan light is still not turned on, you need to locate the burn marks in the socket. It could happen when there is a problem with the wiring or switch. You have to do some troubleshooting to find the location of the electrical issue.
Electrical Problems
After changing the bulb, if the power is still not reaching the socket where you have installed the bulb, then it is time to focus on the wiring. Switch off the power supply before you try to begin contact with wires.
First of all, go through the canopy to make sure that all wires are capped with wire nuts. Locate the loose wiring or a broken wire. If there are any, it can be checked by simply pulling gently on all wires coming from the ceiling. If you find any break off or loose wires, you should call a professional electrician.
The next thing is to examine the light switch to see if it is working. If the light of Hunter fan still does not turn on, try switching off the electricity from the breaker box for more or less 15 minutes and switch it on again. If it doesn’t work too, you need a light kit replacement for your fan.
The wattage limiter may also cause it. According to Hunter’s troubleshooting guide, if you have a ceiling fan from Hunter that was made between 2009 and 2019, you may face problems with the wattage limiter. In this case, you need to contact customer service to get a replacement for it.
A bad regulator could be another problem. To check it, you need to open the components and check the wires by using a voltage checker. If the wire that is linked to the regulator is not getting any voltage, a bad regulator can be the culprit.
If it is happening due to a bad regulator, watch this troubleshooting video to know the procedure in detail:
A Faulty Remote Control
If the ceiling fan lights were working in the beginning and stopped working now, there is a great chance that it is happening due to the remote control if you have it with the fan. The issue could be with the receiver in the fan or the handset.
To fix this, try resetting the remote, it can be done by removing the batteries for 10 seconds before you put them back and turn them on.
You may come across the lights randomly switching on and off on their own. In this case, you need to see if there is an interference between the receiver and the signal of the handset from another source.
If you recently purchased a new remote for your unit, the signal could be set to the same frequency, consequently restricting the fan controls from working. At times, the manufacturers use the same set of RF frequencies which is why it is necessary to make sure that your appliances are working on the different frequencies.
In addition, you should make sure that the remote control is paired with your Hunter fan too. To get instructions on how to do this, check this video to get a step-by-step guide.
How Do You Change A Bulb In A Hunter Ceiling Fan?
It is easy to install and replace Hunter ceiling fans. before you begin, you need to ensure that fan is unplugged from the power source and turned off. The changing of the light bulb relies on the type of light kit you have including a dome fixture, scone light kit and a bowl light kit.
Dome Fixture
hold the top edge firmly and remove the ring cover gently and pull it straight down gently. Remove the screws attaching to the dome fixture. Uninstall the old bulb and add a new one.
Scone Light Kit
Find the screws securing the fixture and remove the scones. Take down the bulbs by moving them anti-clockwise. Add the new bulbs but not too firmly.
Bowl Light Kit
From the middle of the bowl, remove the small decorative stem. To expose the bulb, lower the center cover of the bowl. Remove the old one and change it with a new one. Put the cover bowl and stem back in its position.
How Do You Reset The Light On A Hunter Ceiling Fan?
If you own a Hunter fan and the light isn’t working, it may be happening because it requires the resetting of light. It is a simple process and can be completed in just a few minutes.
Here are the steps you need to follow:
- Switch off the electricity to the ceiling fan at the circuit breaker or fuse box. Then, remove the fixture from its electrical outlet.
- Wait for 30 seconds for the power to disappear from the wires in your house. Remove all bulbs from within the light kit.
- Flick the switch of the fan’s light by turning it on and off three times in rapid succession. The process will reset your fan’s internal circuitry.
- Change the bulbs and plug in the unit. Switch on the power and start using the fan.
Do Hunter Ceiling Fans Have A Lifetime Warranty?
Hunter ceiling fans offer a limited lifetime warranty on the motor. if there is a defect in the motor because of material or workmanship, the step you need to take is to contact customer support, they will assess and change your unit free of cost.
As far as other parts are concerned, the company has a one-year warranty on parts if you see a defect in materials or workmanship.
The light kits’ warranty is based on the type of unit you are using. All light kits usually come with a one-year warranty, but the fixtures that have LED light kit modules have a three-year warranty.
Just keep in mind that the defects will be determined and assessed by Hunter-authorized personnel and you need to provide proof of purchase when you want to claim the warranty.
Final Words
That’s it, we hope that the recommendations above will help you to restore your lights on the Hunter ceiling fan. if you have a defective unit, you need to contact customer support of Hunter through email, website, phone call or on social.
For additional information on Hunter ceiling fan troubleshooting and lighting, you can explore more articles on this website.
My ceiling fan is randomly dimming on its own. My husband turned the light on and one of our 2 light bulbs blew out. The fan will not turn on now.
Please help us!
My 60” Reveille fan is having problems with the switches. The fan is wire to 2 switches one for the fan and one for the light. The switches do not working consistently on turning dan on or turning lights on. I wired exactly a diagram in install booklet shows. I can turn fan on without light switch but I have to turn on fan switch then light switch to get light on, but if I turn light on then fan nothing comes on. Does something need reset. Ultimately I would like to leave fan switch on and control from remote but I want to control light from light switch.